/ * @brief * Get low frequency crystal oscillator clock frequency for target system. * * @note * This is an EFM32 proprietary function, not pa

/ * @brief * Get the Max count of the timer * * @param[in] timer * Pointer to TIMER peripheral register block. * * @return * The max coun

* * WaitTimer_100us * * Wait a multiple of 100us * */

* * WaitTimer_100us * * Wait a multiple of 100us * */

/ * @brief * Get the AUX clock frequency. Used by MSC flash programming and LESENSE, * by default also as debug clock. * * @return * AUX Fr

Check if chr is contained in the string */

* Don't use tpl_disable_all_interrupts_service() and * tpl_enable_all_interrupts_service() because several * functions like 'GetTaskID()' can't be c

============================================================================== * NXT I2C API *======================================================

Compare memory block */

* Control the power supplied to an input sensor */

Output a TCHAR string in defined API encoding */

/ * @brief * Wait for ongoing sync of register(s) to low frequency domain to complete. * * @note * This only applies to the Gecko Family, see

/ Set the value of the clock frequency global variables based on the value of standby_clk passed as parameter. The following global variables ar

Lock a mutex * @param mutex the mutex to lock */

* verify flash pages * * return: * 1: data is flashed correctly * 0: data mismatch occurred */

higher speed write transfer (than transfer8) wait until TX fifo is not full send data

/ * @brief * Load ADC calibration register for a selected reference and conversion mode. * * @details * During production, calibration values

/ * @brief * Write 256 bits of data to a DDATAX register in the CRYPTO module. * * @details * Write 256 bits of data into a DDATAX (Double Dat

/ * @brief * Read 128 bits of data from a DATAX register in the CRYPTO module. * * @details * Read 128 bits of data from a DATAX register in t

/ * @brief * Write variable sized 32 bit data array (max 128 bits) to a DATAX register * * @details * Write variable sized 32 bit array (max 1

/ * @brief * Prepare descriptor for DMA cycle. * * @details * This function prepares the last pieces of configuration required to start a *

/ * @brief * Set DCDC Low-noise RCO band. * * @param[in] band * RCO band to set. ************************************************************

/ * @brief * Set DCDC regulator operating mode * * @param[in] dcdcMode * DCDC mode **********************************************************

* @brief De-initializes the HASH peripheral registers to their default reset values * @param None * @retval None */

* @brief Provides the message digest result. * @note In MD5 mode, Data[7] to Data[4] filed of HASH_MsgDigest structure is not used * an

* @brief Initializes the HASH peripheral according to the specified parameters * in the HASH_InitStruct structure. * @note the hash pro

/ * @brief * LEUART register synchronization freeze control. * * @details * Some LEUART registers require synchronization into the low frequen

/ * @brief * Check if timeout value set with @ref MICROSD_TimeOutSet() has elapsed. * @return * True if timeout has elapsed. *******************

* @brief Waits until the RTC Time and Date registers (RTC_TR and RTC_DR) are * synchronized with RTC APB clock. * @note The RTC Resync

* @brief Configures LED GPIO. * @param Led: Specifies the Led to be configured. * This parameter can be one of following parameters: *

/ * @brief * Get chip major/minor revision. * * @param[out] rev * Location to place chip revision info. *************************************

* @brief Configure the TI1 as Input. * @param TIMx: where x can be 1, 2, 3, 4, 5, 8, 9, 10, 11, 12, 13 or 14 * to select the TIM periph

* @brief Configure the TI2 as Input. * @param TIMx: where x can be 1, 2, 3, 4, 5, 8, 9 or 12 to select the TIM * peripheral. * @param

* @brief C custom defined SHSUB16 for M3 and M0 processors */

\brief Get Base Priority \details Returns the current value of the Base Priority register. \return Base Priority register value *

============================================================================== * Exit a program without cleaning up files. */

This is needed because "netif.c" uses it and without this implementation * this would cause LIBC to be included and that's something we don't want. *

void mcp23s17::attachInterrupt(port p, uint8_t bitNum, itType type,mcpCallBack callback)

* @brief Clips Q31 to Q15 values. */

------------------------------------------------------------------------------ Configure one individual PCIe block. */

Configure the mode. confMask is an OR of all SPR_PCMR_* macros */