* @brief Gets the current sd card data state. * @param hsd: pointer to SD handle * @retval Card state */

* @brief Provides the message digest result. * @param pMsgDigest: Pointer to the message digest * @param Size: The size of the message digest i

* @brief Provides the message digest result. * @param pMsgDigest: Pointer to the message digest * @param Size: The size of the message digest i

* @brief I2C Tx data register flush process. * @param hi2c I2C handle. * @retval None */

* @brief This function handles I2C Communication Timeout for specific usage of STOP flag. * @param hi2c Pointer to a I2C_HandleTypeDef structure t

* @brief Init the JPEG encoding/decoding process in case of Polling or Interrupt and DMA * @param hjpeg: pointer to a JPEG_HandleTypeDef structure

* @brief Check if HSE oscillator Ready * @rmtoll CR HSERDY LL_RCC_HSE_IsReady * @retval State of bit (1 or 0). */

* @brief Get Main PLL division factor for PLLR * @note used for PLLCLK (system clock) * @rmtoll PLLCFGR PLLR LL_RCC_PLL_GetR * @r

* @brief Disable the write protection for RTC registers. * @rmtoll WPR KEY LL_RTC_DisableWriteProtection * @param RTCx RTC In

* @brief Disable the write protection for RTC registers. * @rmtoll WPR KEY LL_RTC_DisableWriteProtection * @param RTCx RTC In

* @brief Enable the write protection for RTC registers. * @rmtoll WPR KEY LL_RTC_EnableWriteProtection * @param RTCx RTC Inst

* @brief Enable the write protection for RTC registers. * @rmtoll WPR KEY LL_RTC_EnableWriteProtection * @param RTCx RTC Inst

* @brief Get Hours format (24 hour/day or AM/PM hour format) * @rmtoll CR FMT LL_RTC_GetHourFormat * @param RTCx RTC Instanc

* @brief Get Hours format (24 hour/day or AM/PM hour format) * @rmtoll CR FMT LL_RTC_GetHourFormat * @param RTCx RTC Instanc

* @brief PTP_GetDevicePropValue * Gets objectInfo and fills object_info structure. * @param phost: Host handle * @param opd: object p

* @brief Return PLL clock frequency used for 48 MHz domain * @retval PLL clock frequency (in Hz) */

@addtogroup RTC_Private_Functions * @{ */ * @brief Enter the RTC Initialization mode. * @note The RTC Initialization mode is write protected,

* @brief Enters the RTC Initialization mode. * @note The RTC Initialization mode is write protected, use the * __HAL_RTC_WRITEPROTECTIO

* @brief Send the Application command to verify that that the next command * is an application specific com-mand rather than a standard co

* @brief Send the Application command to verify that that the next command * is an application specific com-mand rather than a standard co

* @brief Send the Read Multi Block command and check the response * @param SDIOx: Pointer to SDIO register base * @retval HAL status */

* @brief Send the Read Multi Block command and check the response * @param SDMMCx: Pointer to SDMMC register base * @retval HAL status */

* @brief Send the Read Single Block command and check the response * @param SDIOx: Pointer to SDMMC register base * @retval HAL status */

* @brief Send the Read Single Block command and check the response * @param SDMMCx: Pointer to SDMMC register base * @retval HAL status */

* @brief Send the Write Multi Block command and check the response * @param SDIOx: Pointer to SDIO register base * @retval HAL status */

* @brief Send the Write Multi Block command and check the response * @param SDMMCx: Pointer to SDMMC register base * @retval HAL status */

* @brief Send the Write Single Block command and check the response * @param SDIOx: Pointer to SDIO register base * @retval HAL status */

* @brief Send the Write Single Block command and check the response * @param SDMMCx: Pointer to SDMMC register base * @retval HAL status */

* @brief Handle to check BSY flag before start a new transaction. * @param hspi: pointer to a SPI_HandleTypeDef structure that contains *

* @brief Handle the check of the RXTX or TX transaction complete. * @param hspi: SPI handle * @param Timeout : Timeout duration */

* @brief Configures the TIMx External Trigger (ETR). * @param TIMx to select the TIM peripheral * @param TIM_ExtTRGPrescaler: The external Trig

* @brief Time Output Compare 2 configuration * @param TIMx to select the TIM peripheral * @param OC_Config: The output configuration structure

* @brief Handle UART Communication Timeout. * @param huart: UART handle. * @param Flag: specifies the UART flag to check. * @param Status: t

* @brief USBH_MSC_BOT_Process * The function handle the BOT protocol. * @param phost: Host handle * @param lun: Logical Unit Number

* @brief USB_OTG_FlushTxFifo : Flush a Tx FIFO * @param USBx : Selected device * @param num : FIFO number * This parameter can be a v

* @brief C custom defined QSUB8 for M3 and M0 processors */

\brief Send Event Send Event is a hint instruction. It causes an event to be signaled to the CPU. */

* @brief Q15 Circular Read function. */

* @brief Q7 Circular Read function. */

* The peer has failed to authenticate himself using `protocol'. */

-----------------------------------------------------------------------*/ FAT handling - Stretch a chain or Create a new chain */ ---

-----------------------------------------------------------------------*/ Deselect card and release SPI */ ---

* Simple interface to ip_output_if. It finds the outgoing network * interface and calls upon ip_output_if to do the actual work. * * @param p the p

* Sends an IP packet on a network interface. This function constructs * the IP header and calculates the IP header checksum. If the source * IP addr

* Add a network interface to the list of lwIP netifs. * * @param netif a pre-allocated netif structure * @param ipaddr IP address for the new netif

* Write n characters to a ppp link. * RETURN: >= 0 Number of characters written * -1 Failed to write to device */

* Encodes s32_t integer into a pbuf chained ASN1 msg. * * @param p points to output pbuf to encode value into * @param ofs points to the offset wit

* Conversion from ifIndex to lwIP netif * @param ifindex is a s32_t object sub-identifier * @param netif points to returned netif struct pointer */

* Used for specifying the function that should be called when a * LISTENing connection has been connected to another host. * * @param pcb tcp_pcb t

* Print a tcp state for debugging purposes. * * @param s enum tcp_state to print */

* Calculates a new initial sequence number for new connections. * * @return u32_t pseudo random sequence number */

* Called by tcp_process. Checks if the given segment is an ACK for outstanding * data, and if so frees the memory of the buffered data. Next, is plac

* @brief Disable the selected ADC. * @note Prerequisite condition to use this function: ADC conversions must be * stopped. * @param

* @brief This function provides delay (in milliseconds) based on CPU cycles method. * @param mdelay: specifies the delay time length, in milliseco

* @brief Write to a PHY register * @param PHYAddress: PHY device address, is the index of one of supported 32 PHY devices. * This parameter ca

* @brief Error callback. * @param hdfsdm_filter : DFSDM filter handle. * @retval None */

* @brief Error callback. * @param hdfsdm_filter : DFSDM filter handle. * @retval None */

* @brief Initialize the DMA2D according to the specified * parameters in the DMA2D_InitTypeDef and create the associated handle. * @param

* @brief DeInitializes the DMA peripheral * @param hdma: pointer to a DMA_HandleTypeDef structure that contains * the configurati

* @brief FLASH end of operation interrupt callback * @param ReturnValue: The value saved in this parameter depends on the ongoing procedure *

* @brief Initialize the GPIOx peripheral according to the specified parameters in the GPIO_Init. * @param GPIOx: where x can be (A..F) to select t

* @brief Receives in master mode an amount of data in blocking mode. * @param hi2c : Pointer to a I2C_HandleTypeDef structure that contains *

* @brief IRDA error callbacks. * @param hirda: pointer to a IRDA_HandleTypeDef structure that contains * the configuration informa

* @brief IRDA error callback. * @param hirda Pointer to a IRDA_HandleTypeDef structure that contains * the configuration informati

* @brief MMC Abort callbacks * @param hmmc: Pointer MMC handle * @retval None */

* @brief Gets the current mmc card data state. * @param hmmc: pointer to MMC handle * @retval Card state */

* @brief Gets the current mmc card data state. * @param hmmc: pointer to MMC handle * @retval Card state */

* @brief Return the peripheral clock frequency for a given peripheral(SAI..) * @note Return 0 if peripheral clock identifier not managed by this

* @brief Returns the HCLK frequency * @note Each time HCLK changes, this function must be called to update the * right HCLK value.

* @brief Returns the PCLK2 frequency * @note Each time PCLK2 changes, this function must be called to update the * right PCLK2 val

* @brief Wait until the RTC Time and Date registers (RTC_TR and RTC_DR) are * synchronized with RTC APB clock. * @note The RTC Resynchr

* @brief SD Abort callbacks * @param hsd: Pointer SD handle * @retval None */

* @brief Gets the current sd card data state. * @param hsd: pointer to SD handle * @retval Card state */