* @brief Convert a 2 digit decimal to BCD format. * @param Value Byte to be converted * @retval Converted byte */

* @brief Convert a 2 digit decimal to BCD format. * @param Value Byte to be converted * @retval Converted byte */

* @brief Convert a 2 digit decimal to BCD format. * @param Value Byte to be converted * @retval Converted byte */

* @brief Converts a 2 digit decimal to BCD format. * @param Value Byte to be converted * @retval Converted byte */

* @brief Convert a 2 digit decimal to BCD format. * @param Value Byte to be converted * @retval Converted byte */

* @brief Convert a 2 digit decimal to BCD format. * @param Value Byte to be converted * @retval Converted byte */

* @brief Convert a 2 digit decimal to BCD format. * @param Value Byte to be converted * @retval Converted byte */

* Function Name: RZA_IO_RegWrite_32 * Description : IO register 32-bit write * Arguments : volatile uint32_t * ioreg : IO register for writing

* @brief Configure the SDMMC data path according to the specified * parameters in the SDIO_DataInitTypeDef. * @param SDIOx: Pointer to

* @brief Configure the SDMMC data path according to the specified * parameters in the SDIO_DataInitTypeDef. * @param SDIOx: Pointer to

* @brief Send the Data Block Lenght command and check the response * @param SDIOx: Pointer to SDIO register base * @retval HAL status */

* @brief Send the Data Block Lenght command and check the response * @param SDIOx: Pointer to SDIO register base * @retval HAL status */

* @brief Send the Stop Transfer command and check the response. * @param SDMMCx: Pointer to SDMMC register base * @retval HAL status */

* @brief Send the Stop Transfer command and check the response. * @param SDMMCx: Pointer to SDMMC register base * @retval HAL status */

* @brief Send the Stop Transfer command and check the response. * @param SDMMCx: Pointer to SDMMC register base * @retval HAL status */

* @brief Close Transfer and clear flags. * @param hspi: pointer to a SPI_HandleTypeDef structure that contains * the configuration

* @brief Close Transfer and clear flags. * @param hspi: pointer to a SPI_HandleTypeDef structure that contains * the configuration

* @brief Enable register write-protection function * @param None * @return None * @details This function is used to enable regi

/ ! * \brief Insert item into BOD list at the next available opportunity. * * \param pBod Element to insert. * * Insert this BOD

* @brief USB_EP0StartXfer : setup and starts a transfer over the EP 0 * @param USBx Selected device * @param ep pointer to endpoint structure

! * @brief Clears a specified interrupt status. * write 1 clears * @param base USDHC peripheral base address. * @param mask The interrupt status f

\brief Set Base Priority \details Assigns the given value to the Base Priority register. \param [in] basePri Base Priority value to set */

Get buffer's size * \param pBuf pointer to ac_buffer_t structure * \return buffer's size */

/ ! * \brief Find an attribute with the given handle. * * \param handle Attribute handle. * \param pAttrGroup Return value pointer to

/ ! * \brief Register operation handlers. * * \param opType Operation type. * \param execOpCback Execute operation

* Return an iterator to the first element of the sequence. * * @return An iterator to the first element of the sequence. */

/ * Wait for ongoing sync of register(s) to the low-frequency domain to complete. * * @param eusart Pointer to the EUSART peripheral register block.

* @brief Set bytes in memory. If put this code in SRAM, Make sure this code * does not call functions in Flash. * * @return pointer to start of buf

To be re-implemented in the target layer if required

! \brief whether or not to send an ACK \param[in] i2c_periph: I2Cx(x=0,1,2) \param[in] ack: only one parameter can

! \brief whether or not to send an ACK \param[in] i2c_periph: I2Cx(x=0,1) \param[in] ack: \arg I2C_ACK_ENABLE: ACK wil

Silly bit of interface glue - ipv6_routing_table.c doesn't know about interface structures, * but it needs to be able to get from the interface id in

* @brief This function computes the CRC16 residue as defined by CRC ISO/IEC 13239 * @param data input data * @param length Number of bits of DataIn

/ ! * \brief Check if the list is empty or not. * * \param pList Pointer to the list. * * \return True if successfully remov

/ ! * \brief Pack an advertising PDU header. * * \param pBuf Packed packet buffer. * \param pHdr Unpacked PDU header. * * \

/ ! * \brief Convert PHY to PHYS bit. * * \param phy PHY. * * \return PHYS bit. */ /

/ ! * \brief Send internal CIS subsystem message. * * \param pCisCtx CIS context. * \param event CIS event. */ /

/ * @brief * Get the LFnCLK frequency based on the current configuration. * * @param[in] lfClkBranch * Selected LF branch. * * @return *

Log one line of text

* LTC Common code static ******************************************************************************/ ! * @brief Tests the correct key size. *

* LTC Common code static ******************************************************************************/ ! * @brief Tests the correct key size. *

! * @brief Initializes the LTC for symmetric encrypt/decrypt operation. Mode is set to UPDATE. * * @param base LTC peripheral base address * @para

! * @brief Initializes the LTC for symmetric encrypt/decrypt operation. Mode is set to UPDATE. * * @param base LTC peripheral base address * @para

Close an iperf tcp session */

Deal with the fact C library may not _open descriptors 0, 1, 2 - auto bind */

* Set a group using well-known domain parameters */

* Unsigned addition: X = |A| + |B| (HAC 14.7) */

* SHA-1 final digest */

* @ingroup netif * Return the interface for the netif index * * @param idx index of netif to find */

* @ingroup netif_ip6 * Change the state of an IPv6 address of a network interface * (INVALID, TEMPTATIVE, PREFERRED, DEPRECATED, where TEMPTATIVE *

* @brief Function for clearing the specific SAADC event. * * @param[in] saadc_event SAADC event. */

Release a Mutex that was acquired by \ref osMutexAcquire.