* @brief Forces or releases Low Speed APB (APB1) peripheral reset. * @param RCC_APB1Periph: specifies the APB1 peripheral to reset. * T

* @brief Convert from 2 digit BCD to Binary. * @param Value: BCD value to be converted. * @retval Converted word */

* @brief Forces or releases High Speed APB (APB2) peripheral reset. * @param RCC_APB2Periph: specifies the APB2 peripheral to reset. *

! * @details Setup members of package[packageID] * Do basic gate keeping. No api->send call involved */

* @brief Changes the mapping of the specified pin. * @param GPIOx: where x can be (A..I) to select the GPIO peripheral for * STM

* @brief USB_OTG_HC_Halt : Halt channel * @param pdev : Selected device * @param hc_num : channel number * @retval USB_OTG_STS : status */

* @brief HCD_IsDeviceConnected * Check if the device is connected. * @param pdev : Selected device * @retval Device connection status.

* @brief Waits for a FLASH operation to complete. * @param None * @retval FLASH Status: The returned value can be: FLASH_BUSY, FLASH_ERROR_PROGR

* @brief Forces or releases AHB1 peripheral reset. * @param RCC_AHB1Periph: specifies the AHB1 peripheral to reset. * This parameter ca

-------------------------------------------------------------------------- */

* @brief Initializes the GPIOx peripheral according to the specified parameters in the GPIO_InitStruct. * @param GPIOx: where x can be (A..I) to s

* @brief Checks whether the CAN interrupt has occurred or not. * @param CAN_Reg: specifies the CAN interrupt register to check. * @param It_Bit

* @brief USBH_CtlReq * USBH_CtlReq sends a control request and provide the status after * completion of the request * @para

* @brief HCD_GetURB_State * This function returns the last URBstate * @param pdev: Selected device * @retval URB_STATE * */

-------------------------------------------------------------------------- */

* @brief USB_OTG_BSP_mDelay * This function provides delay time in milli sec * @param msec : Value of delay required in milli sec * @

* @brief Converts a 2 digit decimal to BCD format. * @param Value: Byte to be converted. * @retval Converted byte */

* @brief USBH_Free_Pipe * Free the USB host channel * @param idx: Channel number to be freed * @retval Status */

* @brief HCD_SubmitRequest * This function prepare a HC and start a transfer * @param pdev: Selected device * @param hc_num: Channel

* @brief USBH_Alloc_Channel * Allocate a new channel for the pipe * @param ep_addr: End point for which the channel to be allocated *

* @brief USBH_Open_Channel * Open a pipe * @param pdev : Selected device * @param hc_num: Host channel Number * @param dev_addres

* @brief Enables or disables the AHB1 peripheral clock. * @note After reset, the peripheral clock (used for registers read/write access) *

* @brief USBH_BulkSendData * Sends the Bulk Packet to the device * @param pdev: Selected device * @param buff: Buffer pointer from wh

* @brief Initializes the NVIC peripheral according to the specified * parameters in the NVIC_InitStruct. * @note To configure interrupt

* @brief Enters the RTC Initialization mode. * @note The RTC Initialization mode is write protected, use the * RTC_WriteProtectionCmd(

* @brief Checks whether the specified USART flag is set or not. * @param USARTx: where x can be 1, 2, 3, 4, 5, 6, 7 or 8 to select the USART or

* @brief Exits the RTC Initialization mode. * @note When the initialization sequence is complete, the calendar restarts * counting aft

* @brief Enables or disables the specified TIM peripheral. * @param TIMx: where x can be 1 to 14 to select the TIMx peripheral. * @param NewSta

* @brief USB_OTG_FlushTxFifo : Flush a Tx FIFO * @param pdev : Selected device * @param num : FO num * @retval USB_OTG_STS : status */