check the presence of the specified "keyword" string in the current command starting the search from index "index"

non-UI background loop tasks

store script cmd on cmdQueue queue. For example: "M502\nM500\n" will be split into two commands "M502\n", "M500\n"

* @brief Initializes the CRYP Initialization Vectors(IV) according to the * specified parameters in the CRYP_IVInitStruct. * @param CRYP

@brief Draw a rectangle * @param x1 - x point of top left corner * @param y1 - y point of top left corner * @param x2 - x point of bottom right cor

* @brief Writes data in the Data Input FIFO * @param Data: new data of the message to be processed. * @retval None */

* @brief Writes data in the Data Input FIFO * @param Data: new data of the message to be processed. * @retval None */

* @brief Checks whether the specified HASH flag is set or not. * @param HASH_FLAG: specifies the HASH flag to check. * This parameter

* @brief Checks whether the specified HASH flag is set or not. * @param HASH_FLAG: specifies the HASH flag to check. * This parameter c

* @brief Configure the Number of valid bits in last word of the message * @param ValidNumber: Number of valid bits in last word of the message.

* @brief Configure the Number of valid bits in last word of the message * @param ValidNumber: Number of valid bits in last word of the message.

* @brief Starts the message padding and calculation of the final message * @param None * @retval None */

* @brief Starts the message padding and calculation of the final message * @param None * @retval None */

* @brief Checks whether the specified I2C flag is set or not. * @param I2Cx: where x can be 1, 2 or 3 to select the I2C peripheral. * @param

* @brief USBH_CtlReq * USBH_CtlReq sends a control request and provide the status after * completion of the request * @pa

! \brief return the last data entered into the output FIFO \param[in] none \param[out] none \retval last data entered into t

! \brief write data to the IN FIFO \param[in] data: data to write \param[out] none \retval none */

clear and free memory for file list

get the int after config keyword

Test if the byte is DBC 1st byte */

close folder

Compare memory block */

! \brief disable NVIC request \param[in] nvic_irq: the NVIC interrupt request, detailed in IRQn_Type \param[out] none \retval

set probe height to relative position mode

! \brief get USB current frame \param[in] pudev: pointer to USB device \param[out] none \retval USB current frame */

! \brief delay in milliseconds \param[in] msec: value of delay required in milliseconds \param[out] none \retval none */

! \brief set toggle for a pipe \param[in] pudev: pointer to USB core instance \param[in] pp_num: pipe number \param[in] toggle

* @brief Fills each CRYP_KeyInitStruct member with its default value. * @param CRYP_KeyInitStruct: pointer to a CRYP_KeyInitTypeDef structure

@brief Draw a filled rectangle defined with color * @param x1 - x point of top left corner * @param y1 - y point of top left corner * @param x2 - x

@brief Draw a vertical line * @param x - x point of line start * @param y1 - y point of line start * @param y2 - y point of line end */

* @brief Enters the RTC Initialization mode. * @note The RTC Initialization mode is write protected, use the * RTC_WriteProtectionCmd

* @brief Enters the RTC Initialization mode. * @note The RTC Initialization mode is write protected, use the * RTC_WriteProtectionCmd(

* deselect, release SPI bus *************************************************************************************/

port: SPI index baudrate:0-7, 2^(baudrate+1) : 2~256

\brief No Operation No Operation does nothing. This instruction can be used for code alignment purposes. */

add new message to notification queue

! \brief disable the CAU peripheral \param[in] none \param[out] none \retval none */

! \brief initialize the key parameters \param[in] key_initpara: key init parameter struct key_0_high: key 0 high

! \brief initialize the sturct cau_key_initpara \param[in] key_initpara: key init parameter struct key_0_high: key 0 h

! \brief configure the PTP timestamp function \param[in] func: only one parameter can be selected which is shown as below \arg

check and open folder

called by parseAck() to notify PID process status

change probe height

! \brief manage the different states of BOT transfer and updates the status to upper layer \param[in] puhost: pointer to usb host handle

! \brief manage the different states of BOT transfer and updates the status to upper layer \param[in] uhost: pointer to usb host handler

! \brief get USB URB state \param[in] pudev: pointer to USB core instance \param[in] pp_num: pipe number \param[out] none \

* @brief Generic DSI packet header configuration * @param DSIx: Pointer to DSI register base * @param ChannelID: Virtual channel ID of the head

* @brief Sends a data byte through the I2Cx peripheral. * @param I2Cx: where x can be 1, 2 or 3 to select the I2C peripheral. * @param Data:

draw an image from specific address on flash (sx & sy cordinates for top left of image, w width, h height, addr flash byte address)

* @brief Forces or releases AHB2 peripheral reset. * @param RCC_AHB2Periph: specifies the AHB2 peripheral to reset. * This parameter

* @brief Forces or releases AHB2 peripheral reset. * @param RCC_AHB2Periph: specifies the AHB2 peripheral to reset. * This parameter ca

* @brief Exits the RTC Initialization mode. * @note When the initialization sequence is complete, the calendar restarts * counting af

* @brief Exits the RTC Initialization mode. * @note When the initialization sequence is complete, the calendar restarts * counting aft

* @brief Clears the SDIO's interrupt pending bits. * @param SDIO_IT: specifies the interrupt pending bit to clear. * This parameter c

* @brief Initializes the SDIO data path according to the specified * parameters in the SDIO_DataInitStruct. * @param SDIO_DataInitStru

* @brief Checks whether the specified SDIO interrupt has occurred or not. * @param SDIO_IT: specifies the SDIO interrupt source to check. *