@brief Clear a rectangular area * @param x1 - x point of top left corner * @param y1 - y point of top left corner * @param x2 - x point of bottom r

* @brief Forces or releases AHB1 peripheral reset. * @param RCC_AHB1Periph: specifies the AHB1 peripheral to reset. * This parameter

show/draw temperature in a standard menu

! \brief USB control transfer handler \param[in] puhost: pointer to USB host \param[out] none \retval operation status */

! \brief configure USB control status parameters \param[in] puhost: pointer to usb host \param[in] buf: control transfer data buffe

* @brief Enables or disables the CRYP peripheral. * @param NewState: new state of the CRYP peripheral. * This parameter can be: ENABL

* @brief Configures the AES-CCM and AES-GCM phases * @note This function is used only with AES-CCM or AES-GCM Algorithms * @param CRYP_Phase

* @brief Waits for a FLASH operation to complete. * @param None * @retval FLASH Status: The returned value can be: FLASH_BUSY, FLASH_ERROR_PRO

* @brief Changes the mapping of the specified pin. * @param GPIOx: where x can be (A..I) to select the GPIO peripheral. * @param GPIO_PinSour

@brief Draw a filled circle using Bresenham’s Algorithm * @param x0 - x point of circle center * @param y0 - y point of circle center * @param r -

* @brief Returns response received from the card for the last command. * @param SDIO_RESP: Specifies the SDIO response register. * Th

write by page

! \brief get the clock stabilization and periphral reset flags \param[in] flag: the clock stabilization and periphral reset flags, refer

! \brief get the clock stabilization and periphral reset flags \param[in] flag: the clock stabilization and periphral reset flags, refer

* @brief USB_OTG_HC_Halt : Halt channel * @param pdev : Selected device * @param hc_num : channel number * @retval USB_OTG_STS : status */

draw icons in item

check if the value is within min and max limits

* @brief Checks whether the CAN interrupt has occurred or not. * @param CAN_Reg: specifies the CAN interrupt register to check. * @param It_B

* @brief Checks whether the CAN interrupt has occurred or not. * @param CAN_Reg: specifies the CAN interrupt register to check. * @param It_B

* @brief Checks whether the CAN interrupt has occurred or not. * @param CAN_Reg: specifies the CAN interrupt register to check. * @param It_Bit

add new message to toast notification queue

! \brief enable NVIC request \param[in] nvic_irq: the NVIC interrupt request, detailed in IRQn_Type \param[in] nvic_irq_pre_priorit

save dynamic text value (upto 7 characters) ( i : index of the text value position, txt: char * to the text value)

! \brief delay in milli seconds \param[in] msec: value of delay required in milli seconds \param[out] none \retval none */

* @brief Flushes the IN and OUT FIFOs (that is read and write pointers of the * FIFOs are reset) * @note The FIFOs must be flushed onl

* @brief Initializes the CRYP peripheral according to the specified parameters * in the CRYP_InitStruct. * @param CRYP_InitStruct: point

* @brief Initializes the CRYP Keys according to the specified parameters in * the CRYP_KeyInitStruct. * @param CRYP_KeyInitStruct: point

* @brief Enables or disables the High Speed APB (APB2) peripheral clock. * @note After reset, the peripheral clock (used for registers read/writ

\brief Wait For Interrupt Wait For Interrupt is a hint instruction that suspends execution until one of a number of events occurs. */

! \brief handle USB pipe halt \param[in] pudev: pointer to USB core instance \param[in] pp_num: pp_num: host channel number which i

! \brief handle USB pipe halt \param[in] udev: pointer to USB core instance \param[in] pp_num: pp_num: host channel number which is

* @brief Checks whether the last I2Cx Event is equal to the one passed * as parameter. * @param I2Cx: where x can be 1, 2 or 3 to sele

! \brief check whether FMC bank1 is ready or not \param[in] timeout: count of loop \param[out] none \retval state of FMC, re

! \brief clear the FMC flag \param[in] flag: clear FMC flag only one parameter can be selected which is shown as below:

Karl Malbrain's compact CRC-32. See "A compact CCITT crc16 and crc32 C implementation that balances processor cache usage against speed": http://www.g

save settings to Flash only if CRC does not match

* @brief Waits for a Flash operation on Bank2 to complete or a TIMEOUT to occur. * @note This function can be used only for STM32F10x_XL density

@brief Draw a rectangle with predetermined dimensions * @param rect - pointer to rectangle dimensions */

\brief Wait For Event Wait For Event is a hint instruction that permits the processor to enter a low-power state until one of a number of ev

! \brief write to / read from a PHY register \param[in] direction: only one parameter can be selected which is shown as below \arg

! \brief write to / read from a PHY register \param[in] direction: only one parameter can be selected which is shown as below \arg

! \brief get the system clock, bus and peripheral clock frequency \param[in] clock: the clock frequency which to get onl

send emergency command now. The command parameter must be a clear command, not formatted NOTE: Make sure that the printer can receive the command

! \brief USB control transfer handler \param[in] uhost: pointer to USB host \param[out] none \retval operation status */

! \brief configure USB control status parameters \param[in] uhost: pointer to usb host \param[in] buf: control transfer data buffer

* @brief Waits for a Flash operation on Bank1 to complete or a TIMEOUT to occur. * @note This function can be used for all STM32F10x devices,

@brief Draw a filled rectangle * @param x1 - x point of top left corner * @param y1 - y point of top left corner * @param x2 - x point of bottom ri

* @brief Converts a 2 digit decimal to BCD format. * @param Value: Byte to be converted. * @retval Converted byte */

* @brief Converts a 2 digit decimal to BCD format. * @param Value: Byte to be converted. * @retval Converted byte */

* @brief USB_OTG_BSP_mDelay * This function provides delay time in milli sec * @param msec : Value of delay required in milli sec

\brief Data Synchronization Barrier This function acts as a special kind of Data Memory Barrier. It completes when all explicit memory acces

edit an integer value in a standard menu

! \brief check whether FMC bank1 is ready or not \param[in] timeout: count of loop \param[out] none \retval state of FMC, re

! \brief GPIO parameter initialization \param[in] gpio_periph: GPIOx(x = A,B,C,D,E,F,G) \param[in] mode: gpio pin mode

! \brief get the system clock, bus and peripheral clock frequency \param[in] clock: the clock frequency which to get onl

show live info text on icons

* @brief Flushes the IN and OUT FIFOs (that is read and write pointers of the * FIFOs are reset) * @note The FIFOs must be flushed o

* @brief Checks whether the specified CRYP flag is set or not. * @param CRYP_FLAG: specifies the CRYP flag to check. * This parameter

* @brief Initializes the CRYP peripheral according to the specified parameters * in the CRYP_InitStruct. * @param CRYP_InitStruct: poi

* @brief Initializes the CRYP Keys according to the specified parameters in * the CRYP_KeyInitStruct. * @param CRYP_KeyInitStruct: poi

* @brief Fills each CRYP_KeyInitStruct member with its default value. * @param CRYP_KeyInitStruct: pointer to a CRYP_KeyInitTypeDef structure *

* @brief HCD_GetURB_State * This function returns the last URBstate * @param pdev: Selected device * @retval URB_STATE * */

* @brief HCD_SubmitRequest * This function prepare a HC and start a transfer * @param pdev: Selected device * @param hc_num: Chann

! \brief enable the CAU peripheral \param[in] none \param[out] none \retval none */

! \brief flush the IN and OUT FIFOs \param[in] none \param[out] none \retval none */

! \brief initialize the CAU peripheral \param[in] algo_dir: algorithm direction only one parameter can be selected which