Selects the given dataflash chip. * * \param[in] ChipMask Mask of the Dataflash IC to select, in the form of a \c DATAFLASH_CHIPn mask (whe

Waits while the target's NVM controller is busy performing an operation, exiting if the * timeout period expires. * * \return Boolean \c true if

Detaches the device from the USB bus. This has the effect of removing the device from any * attached host, ceasing USB communications. If no host

Inline Functions: */

---------------------------------------------------------------------------*/ * Reset the timer with the same interval. * * This function resets the

-----------------------------------------------------------------------------*/

Sends a byte to the currently selected dataflash IC, and ignores the next byte from the dataflash. * * \param[in] Byte Byte of data to send

Sends a byte to the currently selected dataflash IC, and ignores the next byte from the dataflash. * * \param[in] Byte Byte of data to send

Sends a byte to the currently selected dataflash IC, and ignores the next byte from the dataflash. * * \param[in] Byte Byte of data to send

Sends a byte to the currently selected dataflash IC, and ignores the next byte from the dataflash. * * \param[in] Byte Byte of data to send

Sends a byte to the currently selected dataflash IC, and ignores the next byte from the dataflash. * * \param[in] Byte Byte of data to send

Sends a byte to the currently selected dataflash IC, and ignores the next byte from the dataflash. * * \param[in] Byte Byte of data to send

Sends a byte to the currently selected dataflash IC, and ignores the next byte from the dataflash. * * \param[in] Byte Byte of data to send

Event handler for the library USB Connection event. */

Event handler for the USB_DeviceEnumerationFailed event. This indicates that a problem occurred while * enumerating an attached USB device. */

Sends an IN packet to the host on the currently selected endpoint, freeing up the endpoint for the * next packet and switching to the alternative

Acknowledges an OUT packet to the host on the currently selected endpoint, freeing up the endpoint * for the next packet and switching to the alt

Writes four bytes to the currently selected endpoint's bank in big endian format, for IN * direction endpoints. * * \ingroup Group_Endpo

Writes four bytes to the currently selected endpoint's bank in little endian format, for IN * direction endpoints. * * \ingroup Group_En

Asserts or deasserts the target's reset line, using the correct polarity as set by the host using a SET PARAM command. * When not asserted, the line

Sends and receives a byte of ISP data to and from the attached target, using the * appropriate SPI hardware or software routines depending on the

Function to receive the given encapsulated RNDIS response from the device. * * \param[out] Buffer Destination command data buffer to write read da

Function to send the given encapsulated RNDIS command to the device. * * \param[in] Buffer Source command data buffer to send to the device * \p

Function to receive a PIMA response container from the attached still image device. * * \return A value from the Pipe_Stream_RW_ErrorCodes_t enum

Sends and receives a byte through the USART SPI interface, blocking until the transfer is complete. * * \param[in] DataByte Byte to send thr

Resumes USB communications with an attached and enumerated device, by resuming the transmission * of the 1MS Start Of Frame messages to the devic

Busy-waits while the NVM controller is busy performing a NVM operation, such as a FLASH page read or CRC * calculation. * * \return Boolean \c tr

Sends an IDLE via the USART to the attached target, consisting of a full frame of idle bits. */

---------------------------------------------------------------------------*/

---------------------------------------------------------------------------*/ * Check if a timer has expired. * * This function tests if a timer has

-----------------------------------------------------------------------------------*/ * Prepend Ethernet header to an outbound IP packet and see if we

UIP_CONF_IPV6 */ ---------------------------------------------------------------------------*/

Audio class driver callback for the setting and retrieval of streaming endpoint properties. This callback must be implemented * in the user applicat

Audio class driver callback for the setting and retrieval of streaming interface properties. This callback must be implemented * in the user applica

Gets and status and verifies whether an error occurred. */

Checks to see if the nominated IP address has already been allocated to a client. * * \param[in] IPAddress IP Address whose lease status should be

Fills the DHCP packet response with the appropriate BOOTP header for DHCP. This fills out all the required * fields, leaving only the additional DHC

Selects the given dataflash chip. * * \param[in] ChipMask Mask of the Dataflash IC to select, in the form of a \c DATAFLASH_CHIPn mask (whe

Selects the given dataflash chip. * * \param[in] ChipMask Mask of the Dataflash IC to select, in the form of a \c DATAFLASH_CHIPn mask (whe

Selects the given dataflash chip. * * \param[in] ChipMask Mask of the Dataflash IC to select, in the form of a \c DATAFLASH_CHIPn mask (whe

Selects the given dataflash chip. * * \param[in] ChipMask Mask of the Dataflash IC to select, in the form of a \c DATAFLASH_CHIPn mask (whe

Selects the given dataflash chip. * * \param[in] ChipMask Mask of the Dataflash IC to select, in the form of a \c DATAFLASH_CHIPn mask (whe

Selects the given dataflash chip. * * \param[in] ChipMask Mask of the Dataflash IC to select, in the form of a \c DATAFLASH_CHIPn mask (whe

Routine to discard the specified number of bytes from the control endpoint stream. This is used to * discard unused bytes in the stream from the hos

Event handler for the USB device Start Of Frame event. */