Strip whitespace chars off end of given string, in place. Return s. */

unrefers all fds that this cache page refers to and releases the cache page

frees cached page

Find free object lookup entry Iterate over object lookup pages in each block until a free object id entry is found

searches in the object indices and returns the referenced page index given the object id and the data span index destroys fs->lu_work

populates index map, from vector entry start to vector entry end, inclusive

TCPM driver wrapper function */

Memcopy with strictly ordered memory access, e.g. for register targets. * \param dst Destination data is copied to. * \param src Source data is copied

* @brief Wait for a FLASH CRC computation to complete. * @param Timeout maximum flash operation timeout * @param Bank flash FLASH_BANK_1 or FLA

* @brief Disables dynamically FMC_NORSRAM write operation. * @param Device Pointer to NORSRAM device instance * @param Bank NORSRAM bank number

* @brief ADC error callback in non-blocking mode * (ADC conversion with interruption or transfer by DMA). * @note In case of error due

* @brief Slave Address Match callback. * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains * the configuration i

* @brief Aborts the MDMA Transfer. * @param hmdma : pointer to a MDMA_HandleTypeDef structure that contains * the configuration

* @brief Disables a device specific interrupt in the NVIC interrupt controller. * @param IRQn External interrupt number. * This paramete

* @brief Data OUT stage callback. * @param hpcd PCD handle * @param epnum endpoint number * @retval None */

* @brief Enable the USB voltage level detector. * @retval None. */

* @brief Returns the PCLK1 frequency * @note Each time PCLK1 changes, this function must be called to update the * right PCLK1 value. O

* @brief Gets the current sd card data state. * @param hsd: pointer to SD handle * @retval Card state */

* @brief SPI Abort Complete callback. * @param hspi SPI handle. * @retval None */

* @brief Get the selected ADC instance disable state. * @rmtoll CR ADDIS LL_ADC_IsDisableOngoing * @param ADCx ADC instance * @

* @brief Stop ADC group regular conversion. * @note On this STM32 series, setting of this feature is conditioned to * ADC state: *

* @brief Initialize GPIO registers according to the specified parameters in GPIO_InitStruct. * @param GPIOx GPIO Port * @param GPIO_InitStruct p

* @brief Check if LSI is Ready * @rmtoll CSR LSIRDY LL_RCC_LSI_IsReady * @retval State of bit (1 or 0). */

* @brief Get the oscillator used as PLL clock source. * @rmtoll PLLCKSELR PLLSRC LL_RCC_PLL_GetSource * @retval Returned value can be

* @brief Switches the MMC card to Double Data Rate (DDR) mode. * @param hmmc: MMC handle * @param state: State of DDR mode * @retval MMC Card

* @brief Send the Erase command and check the response * @param SDMMCx Pointer to SDMMC register base * @param EraseType Type of erase to be pe

* @brief Send the Go Idle State command and check the response. * @param SDMMCx: Pointer to SDMMC register base * @retval HAL status */

* @brief Return the command index of last command for which response received * @param SDMMCx: Pointer to SDMMC register base * @retval Command

* @brief Switches the SD card to Ultra High Speed mode. * This API must be used after "Transfer State" * @note This operation should be

* @brief Handle SPI Communication Timeout. * @param hspi: pointer to a SPI_HandleTypeDef structure that contains * the configuration

* @brief Timer Output Compare 1 configuration * @param TIMx to select the TIM peripheral * @param OC_Config The output configuration structure

* @brief Configure the Polarity and Filter for TI1. * @param TIMx to select the TIM peripheral. * @param TIM_ICPolarity The Input Polarity. *

* @brief Configure the TI1 as Input. * @param TIMx to select the TIM peripheral. * @param TIM_ICPolarity The Input Polarity. * This

* @brief USB_DevDisconnect : Disconnect the USB device by disabling Rpu * @param USBx Selected device * @retval HAL status */

* @brief Returns USB core mode * @param USBx Selected device * @retval return core mode : Host or Device * This parameter can be one

* @brief USB_SetDevSpeed Initializes the DevSpd field of DCFG register * depending the PHY type and the enumeration speed of the device.

* @brief USB_WritePacket : Writes a packet into the Tx FIFO associated * with the EP/channel * @param USBx Selected device * @param

* @brief Helper function to calculate the PLL frequency output * @param PLLInputFreq PLL Input frequency (based on HSE/(HSI/HSIDIV)/CSI) * @para

* XMODEM Transmit **********************************************************************************************************************/

Scan a single key, ID is the key number from 0, gpio is pin number Should be called at ~10ms interval Return value: 0 when nothing pressed 1 when shor

Return pointer to first char (of chars) or inline comment in given string, or pointer to NUL at end of string if neither found. Inline comment must

* Returns type C current limit (mA) based upon cc_voltage (mV). */

* Enter default mode ( payload[0] == 0 ) or attempt to enter mode via svid & * opos */

Executes the given shell command 'interactive_mode' is 1 if invoked directly from the interactive shell, 0 otherwise Returns a pointer to the shell_co

returns cached page for give page index, or null if no such cached page

djb2 hash