/ ! * \brief Get the current BB clock value in microseconds. * * \return Current BB clock value, units are microseconds. * * This rou

Public function, see header qcbor.h file */

* @brief Configure the PLL3 VCI,VCO ranges, multiplication and division factors and enable it * @param pll3: Pointer to an RCC_PLL3InitTypeDef str

* @brief Send the Stop Transfer command and check the response. * @param SDMMCx: Pointer to SDMMC register base * @retval HAL status */

* @brief Send the Stop Transfer command and check the response. * @param SDIOx: Pointer to SDIO register base * @retval HAL status */

* @brief Send the Stop Transfer command and check the response. * @param SDIOx: Pointer to SDIO register base * @retval HAL status */

* @brief Send the Stop Transfer command and check the response. * @param SDIOx: Pointer to SDIO register base * @retval HAL status */

Output a debug message * * @param format printf-style format string, followed by variables */

/ ! * \brief Pass an event to the device privacy module. * * \param event Device privacy event. * \param param DM or Privacy e

! \brief check whether peripheral and channels match \param[in] dma_periph: DMAx(x=0,1) \arg DMAx(x=0,1) \param[in] ch

* Return an iterator to the element following the last element of the sequence. * * @return An iterator to the element following the last el

/ ! * \brief Find a CIG by CIG ID. * * \param cigId CIG identifier. * * \return CIG or NULL if not found. */ /

* AES-ECB block encryption/decryption */

* Get the type of a curve */

* Convert numeric IPv6 address string to a binary. * IPv4 tunnelling addresses are not covered. * \param ip6addr IPv6 address in string format. * \

Allocate a pcb and set up the test_tcp_counters_* callbacks */

* @brief Disable the selected ADC. * @note Prerequisite condition to use this function: ADC conversions must be * stopped. * @param

! * @brief Disable the clock for specific IP. * * @param name Which clock to disable, see \ref clock_ip_name_t. */

! * @brief Enable the clock for specific IP. * * @param name Which clock to enable, see \ref clock_ip_name_t. */

/ * @brief * Write 256 bits of data to a DDATAX register in the CRYPTO module. * * @details * Write 256 bits of data into a DDATAX (Double Dat

* @brief Writes Key in Key registers. * @param hcryp pointer to a CRYP_HandleTypeDef structure that contains * the configuration informa

* Function Name: Cy_PRA_Init ****************************************************************************/ * * Initializes the PRA driver: * - Initial

* @brief This function allows to get the channel number from channel instance. * @param Instance DFSDM channel instance. * @retval Channel numbe

* @brief Wait for a FLASH operation to complete. * @param Timeout maximum flash operationtimeout * @retval HAL Status */

* @brief This function handles FMPI2C Communication Timeout. * @param hfmpi2c Pointer to a FMPI2C_HandleTypeDef structure that contains *

\brief Notify host (__exit message) side that test suite execution was complete * \result Test suite result * \details If __exit is not received b

* @brief This function handles I2C Communication Timeout. * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains *

* @brief This function handles I2C Communication Timeout. * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains *

* @brief This function handles I2C Communication Timeout. * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains *

* @brief This function handles I2C Communication Timeout. * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains *

* @brief This function handles I2C Communication Timeout. * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains *

* @brief This function handles I2C Communication Timeout. * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains *

* @brief This function handles I2C Communication Timeout. * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains *

* @brief This function handles I2C Communication Timeout. * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains *

* @brief This function handles I2C Communication Timeout. * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains *

* @brief This function handles I2C Communication Timeout. * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains *

* @brief This function handles I2C Communication Timeout. * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains *

* @brief This function handles I2C Communication Timeout. * @param hi2c Pointer to a I2C_HandleTypeDef structure that contains *

/ ! * \brief Send an L2CAP data packet on the given CID. * * \param cid The channel identifier. * \param handle The connection hand

* @brief Generic function to start a PKA operation in blocking mode. * @param hpka PKA handle * @param mode PKA operation * @param Timeout T

* @brief Generic function to start a PKA operation in non-blocking mode with Interrupt. * @param hpka PKA handle * @param mode PKA operation

@defgroup HAL_SDMMC_LL_Group5 Responses management functions * @brief Responses functions * @verbatim ==========================================

@defgroup HAL_SDMMC_LL_Group5 Responses management functions * @brief Responses functions * @verbatim ========================================

@defgroup HAL_SDMMC_LL_Group5 Responses management functions * @brief Responses functions * @verbatim ========================================

@defgroup HAL_SDMMC_LL_Group5 Responses management functions * @brief Responses functions * @verbatim ========================================

* @brief Handle SMBUSx communication when starting transfer or during transfer (TC or TCR flag are set). * @param hsmbus SMBUS handle. * @param

/ * @brief * Get the current core clock frequency. * * @details * Calculate and get the current core clock frequency based on the current *

@brief Check if a UsefulBufC is NULL or not @param[in] UB The UsefulBufC to check @return 1 if it is NULL, 0 if not. */

/ ! * \brief Send an error response PDU. * * \param handle The connection handle. * \param opcode Opcode of the request that generated

/ ! * \brief Clear IFS in operation. * * The BB may choose not to enable IFS after the next Tx or Rx. */ /

* Make sure buffer has enough room for header. * * \param buf buffer to check * \param size required header space * \return a pointer of type buff

/ ! * \brief Return the connection control block for the given connection ID. * * \param connId Connection ID. * * \return Pointer to CCB o

Remove the './' prefix, if present. This function assumes that resources.win_to_unix() replaced all windows backslashes with

! \brief check whether FMC is ready or not \param[in] none \param[out] none \retval state of FMC \arg FMC_READY

/ ! * \brief Stop LLCP timer. * * \param pCtx Connection context. */ /

* Get PHY time stamp. * * \param rf_mac_setup pointer to MAC * \return Timestamp from PHY * */

* Copy the contents of a point */

* Sliding-window exponentiation: X = A^E mod N (HAC 14.85) */