Inline Functions: */

Inline Functions: */

Macros: */

Macros: */

Resets the USB bus, including the endpoints in any attached device and pipes on the AVR host. * USB bus resets leave the default control pipe con

Resets the USB bus, including the endpoints in any attached device and pipes on the AVR host. * USB bus resets leave the default control pipe con

Inline Functions: */

Check the non-volatile storage in the EEPROM for the proper magic value, and erase the parameter area if the magic * value was not correct. */

Retrieves the host PC read/write privileges for a given parameter in the parameter table. This should * be called before calls to \ref V2Params_GetP

Loads saved non-volatile parameter values from the EEPROM into the parameter table, as needed. */

Sets the value for a given parameter in the parameter table. * * \note This function does not first check for write privileges - if the value is be

Handler for the CMD_SET_PARAMETER and CMD_GET_PARAMETER commands from the host, setting or * getting a device parameter's value from the parameter t

Handler for the CMD_LOAD_ADDRESS command, loading the given device address into a * global storage variable for later use, and issuing LOAD EXTENDED

Handler for the CMD_RESET_PROTECTION command, implemented as a dummy ACK function as * no target short-circuit protection is currently implemented.

Handler for the CMD_SIGN_ON command, returning the programmer ID string to the host. */

Handler for unknown V2 protocol commands. This discards all sent data and returns a * STATUS_CMD_UNKNOWN status back to the host. * * \param[in]

Reads a block of data from the virtual FAT filesystem, and sends it to the * host via the USB Mass Storage interface. * * \param[in] BlockNumber

Writes a block of data to the virtual FAT filesystem, from the USB Mass * Storage interface. * * \param[in] BlockNumber Index of the block to w

Writes a byte of EEPROM out to the EEPROM memory space. * * \note This function is required as the avr-libc EEPROM functions do not cope *

Writes a report to the attached device. * * \param[in] ReportOUTData Buffer containing the report to send to the device * \param[in] ReportLengt

Inline Functions: */ Write a value to a location protected by the XMEGA CCP protection mechanism. This function uses inline assembly to ensure that

Removes access to the target's NVM controller and physically disables the target's physical PDI interface. */

Enables the physical PDI interface on the target and enables access to the internal NVM controller. * * \return Boolean \c true if the PDI interfac

Erases a specific memory space of the target. * * \param[in] EraseCommand NVM erase command to send to the device * \param[in] Address Add

Retrieves the CRC value of the given memory space. * * \param[in] CRCCommand NVM CRC command to issue to the target * \param[out] CRCDest C

Reads memory from the target's memory spaces. * * \param[in] ReadAddress Start address to read from within the target's address space * \param[

Writes byte addressed memory to the target's memory spaces. * * \param[in] WriteCommand Command to send to the device to write each memory byte

Writes page addressed memory to the target's memory spaces. * * \param[in] WriteBuffCommand Command to send to the device to write a byte to the

Handler for the CMD_XPROG command, which wraps up XPROG commands in a V2 wrapper which need to be * removed and processed so that the underlying XPR

Handler for the XPROG ENTER_PROGMODE command to establish a connection with the attached device. */

Handler for the XPRG ERASE command to erase a specific memory address space in the attached device. */

Handler for the XPROG LEAVE_PROGMODE command to terminate the PDI programming connection with * the attached device. */

Handler for the XPROG CRC command to read a specific memory space's CRC value for comparison between the * attached device's memory and a data set o

Handler for the XPROG READ_MEMORY command to read data from a specific address space within the * attached device. */

Handler for the CMD_XPROG_SETMODE command, which sets the programmer-to-target protocol used for PDI/TPI * programming. */

Handler for the XPROG SET_PARAM command to set a XPROG parameter for use when communicating with the * attached device. */

Handler for the XPROG WRITE_MEMORY command to write to a specific memory space within the attached device. */

Disables the target's PDI interface, exits programming mode and starts the target's application. */

Disables the target's TPI interface, exits programming mode and starts the target's application. */

Enables the target's PDI interface, holding the target in reset until PDI mode is exited. */

Enables the target's TPI interface, holding the target in reset until TPI mode is exited. */

Initialise the clock

-----------------------------------------------------------------------*/ Put a string to the file */ ---

-----------------------------------------------------------------------*/ Put a string to the file */ ---