******************************************************************************* ** \brief Clear conversion status flag of sequence A or sequence B.

******************************************************************************* ** \brief Reading the data of the specified channel(s). ** ** \p

******************************************************************************* ** \brief Get the conversion status flag. ** ** \param [in] ADCx

******************************************************************************* ** \brief Get the value of a specified channel via channel index.

******************************************************************************* ** \brief Start an ADC conversion. ** ** \param [in] ADCx

******************************************************************************* ** \brief Stop an ADC conversion and clear flags. ** ** \param [

******************************************************************************* ** \brief Enable or disable the specified can acceptance filter.

******************************************************************************* ** \brief Configures the can acceptance filter ** ** \param [i

******************************************************************************* ** \brief The configuration of the specified dma channel. ** **

******************************************************************************* ** \brief Enable or disable the specified dma channel. ** ** \p

******************************************************************************* ** \brief Enable or disable the dma. ** ** \param [in] pstcDma

******************************************************************************* ** \brief Set The DMA trigger source. ** ** \param [in] pstcDm

******************************************************************************* ** \brief Provides the message digest result. ** ** \param [ou

******************************************************************************* ** \brief Set the baudrate for I2C peripheral. ** \param [in] pstc

******************************************************************************* ** \brief I2C generate start condition ** \param [in] pstcI2Cx

******************************************************************************* ** \brief ISR for NMI ** ***************************************

******************************************************************************* ** \brief Calculate the value of temperature. ** ** \retval A floa

******************************************************************************* ** \brief Special control register Setting ** ** \param [in]

* Function implementation - global ('extern') and local ('static') ******************************************************************************/ *

******************************************************************************* ** \brief Clock backup before enter stop mode and mark it. ** *

******************************************************************************* ** \brief Clock recover after wakeup stop mode. ** ** \param N

******************************************************************************* ** \brief Enable or disable the FCG1 peripheral clock. ** ** \n

******************************************************************************* ** \brief Enable or disable the FCG3 peripheral clock. ** ** \n

******************************************************************************* ** \brief NVIC backup and disable before entry from stop mode **

******************************************************************************* ** \brief NVIC recover after wakeup from stop mode ** ** param

\brief Enable I-Cache \details Turns on I-Cache */

******************************************************************************* ** \brief SRAM ECC/Parity check register disable function ** **

******************************************************************************* ** \brief SRAM ECC/Parity check register enable function ** ** \

* Function implementation - global ('extern') and local ('static') ******************************************************************************/ *

******************************************************************************* ** \brief SRAM read, write wait cycle register enable function **

******************************************************************************* ** \brief Set synchronous clock mode baudrate ** ** \param [in]

******************************************************************************* ** \brief Set smart card mode baudrate ** ** \param [in] USARTx

******************************************************************************* ** \brief Set synchronous clock mode baudrate ** ** \param [in]

******************************************************************************* ** \brief Set UART mode baudrate ** ** \param [in] USARTx

\brief System Tick Configuration \details Initializes the System Timer and its interrupt, and starts the System Tick Timer. Counter is

* @brief Setup the external memory controller. * Called in startup_stm32f1xx_xx.s/.c before jump to main. * This function config

* @brief Setup the external memory controller. * Called in startup_stm32f4xx.s before jump to main. * This function configures th

* @brief Setup the external memory controller. * Called in startup_stm32f2xx.s before jump to main. * This function configures th

******************************************************************************* ** \brief Initialize Timera unit base function ** ** \param [in]

******************************************************************************* ** \brief Enable or disable Timera compare function ** ** \param

******************************************************************************* ** \brief Initialize Timera unit compare function ** ** \param [

******************************************************************************* ** \brief Timera hardware startup Config ** ** \param [in] TIMER

******************************************************************************* ** \brief Set Timera compare value ** ** \param [in] TIMERAx

\brief Set Interrupt Priority (non-secure) \details Sets the priority of a non-secure device specific interrupt or a non-secure processor exceptio

******************************************************************************* ** \brief Read UART data buffer ** ** \param [in] USARTx

****************************************************************************** ** \brief Write UART data buffer ** ** \param [in] USARTx

******************************************************************************* ** \brief Set USART baudrate ** ** \param [in] USARTx

* Function implementation - global ('extern') and local ('static') ******************************************************************************/ *

Hardware timer IRQ handler - dispatch software timers

Symbol constructor -- not intended to be called directly by Kconfiglib clients.