Function bind Description Request to bind a socket on a local address. Return Author Ahmed Ezzat Version 1.0 Date 5 June 2012 ********

* @brief This function established the connection for the channel in Active (client) mode. * This function waits for the untill the connection is

Compute a Dallas Semiconductor 8 bit CRC. These show up in the ROM and the registers. (note: this might better be done without to table, it would pro

* @brief This function used for disconnect the socket and parameter is "s" which represent the socket number * @return 1 for success else 0. */

* Returns a char[13], representing the Code Word to be send. * * getCodeWordA(char*, char*) * */

* Returns a char[13], representing the Code Word to be send. * A Code Word consists of 9 address bits, 3 data bits and one sync bit but in our case o

* Like getCodeWord (Type C = Intertechno) */

Send Message to the Hub

public

attempt to determine if the device at the given address is connected to the bus

! @fn \ sint8 m2m_ate_get_rx_status(uint8); @brief This function used to return status of RX test case either running or stopped. @return The fun

=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=* STATIC FUNCTIONS *=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=

! @fn NMI_API sint8 m2m_wifi_get_mac_address(uint8 *pu8MacAddr) @brief Request the current MAC address of the device (the working mac a

* @fn nm_bsp_reset * @brief Reset NMC1500 SoC by setting CHIP_EN and RESET_N signals low, * CHIP_EN high then RESET_N high * @author M.

* @fn nm_bus_iface_deinit * @brief Deinitialize bus interface * @return M2M_SUCCESS in case of success and M2M_ERR_BUS_FAIL in case of failure * @aut

* @fn nm_bus_iface_init * @brief Initialize bus interface * @return M2M_SUCCESS in case of success and M2M_ERR_BUS_FAIL in case of failure * @author

* @fn nm_get_firmware_info(tstrM2mRev* M2mRev) * @brief Get Firmware version info * @param [out] M2mRev * pointer holds address of structure "t

* @fn nm_get_firmware_info(tstrM2mRev* M2mRev) * @brief Get Firmware version info * @param [out] M2mRev * pointer holds address of structure "t

* @fn nm_i2c_read_reg_with_ret * @brief Read register with error code return * @param [in] u32Addr * Register address * @param [out] pu32RetVal *

* @fn nm_spi_init * @brief Initialize the SPI * @return M2M_SUCCESS in case of success and M2M_ERR_BUS_FAIL in case of failure * @author M. Abdelmawl

* @fn nm_spi_read_reg * @brief Read register * @param [in] u32Addr * Register address * @return Register value * @author M. Abdelmawla * @date 11

* @fn nm_spi_write_reg * @brief write register * @param [in] u32Addr * Register address * @param [in] u32Val * Value to be written to the regis

* @brief Returns the first byte in the receive queue (no checking) * * @return */

Return the IP address of the host who sent the current incoming packet

Return the port of the host who sent the current incoming packet

sends command for all devices on the bus to perform a temperature conversion

You need to use this function to start a search again from the beginning. You do not need to do it for the first search, though you could.

Perform a search. If this function returns a '1' then it has enumerated the next device and you may retrieve the ROM from the OneWire::address variabl

* @brief This function used to send the data in TCP mode * @return 1 for success else 0. */

* Sends a "Sync" Bit * _ * Waveform Protocol 1: | |_______________________________ * _ * Waveform Prot

* Sets the protocol to send. */

* Sets Repeat Transmits */

* @fn spi_flash_pp * @brief Program data of size less than a page (256 bytes) at the SPI flash * @param[IN] u32Offset * Address to write to at

* @fn spi_flash_read_internal * @brief Read from data from SPI flash * @param[OUT] pu8Buf * Pointer to data buffer * @param[IN] u32Addr * A

stategy 3 - start a timer and perform a sort of polling

strategy 1 - attach external interrupt to change pin (works on 328)

return number of bytes available in the current packet, will return zero if parsePacket hasn't been called yet */

Start EthernetUDP socket, listening at local port PORT */

returns: 0/DHCP_CHECK_NONE: nothing happened 1/DHCP_CHECK_RENEW_FAIL: renew failed 2/DHCP_CHECK_RENEW_OK: renew success 3/DHCP_CHECK_R

* Turns a decimal value to its binary representation */

* Disable receiving data */

* Enable receiving data */

* Enable transmissions * * @param nTransmitterPin Arduino Pin to which the sender is connected to */

Fetch temperature for device index

Fetch temperature for device index

=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=* STATIC FUNCTIONS *=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=

Function gethostbyname Description Return None. Author Ahmed Ezzat Version 1.0 Date 4 June 2012 ***************************************

* @fn NMI_API sint8 hif_deinit(void * arg); * @brief To De-initialize HIF layer. * @param [in] arg * Pointer to the arguments. * @return Th