* @brief Check if MSI clock range is selected with MSIRANGE register * @rmtoll CR MSIRGSEL LL_RCC_MSI_IsEnabledRangeSelect * @retv

* @brief Convert from 2 digit BCD to Binary. * @param Value BCD value to be converted * @retval Converted word */

* Signed addition: X = A + B */

* The Low level function to read register contents from Hardware. * * @param[in] pointer to the base of register map * @param[in] Offset from the b

! * @brief Clears the DSPI status flag. * * This function clears the desired status bit by using a write-1-to-clear. The user passes in the base a

! * @brief Clears the DSPI status flag. * * This function clears the desired status bit by using a write-1-to-clear. The user passes in the base a

! * @brief Clears the DSPI status flag. * * This function clears the desired status bit by using a write-1-to-clear. The user passes in the base a

! * @brief Clears the DSPI status flag. * * This function clears the desired status bit by using a write-1-to-clear. The user passes in the base a

! * @brief Clears the DSPI status flag. * * This function clears the desired status bit by using a write-1-to-clear. The user passes in the base a

\brief Enables the given interrupt using GIC's ISENABLER register. * \param [in] IRQn The interrupt to be enabled. */

* @brief Abort the DMA Transfer. * @param hdma pointer to a DMA_HandleTypeDef structure that contains * the configuration informat

* @brief Handles I2Cx communication when starting transfer or during transfer (TC or TCR flag are set). * @param hi2c I2C handle. * @param DevA

* @brief Get the lock with 1-step lock. * @rmtoll RLR LOCK LL_HSEM_1StepLock * @rmtoll RLR COREID LL_HSEM_1Step

Public functions for closing arrays and maps. See header qcbor.h */

* @brief Wait RTC Access Enable * * @param None * * @return None * * @details This function is used to enable the maximum

* Function Name: R_CAN_Control * Description : Controls transition to CAN grobal modes or CAN channle modes * determined by the CAN Co

* Import from an ASCII string */

* Return the total size in bytes */

* \brief Push Buffer to Protocol Core. * * \param buf pointer to buffer. NULL is accepted and ignored. */

LWIP_DEBUG_TIMERNAMES */

! * @brief Enable the clock for specific IP. * * @param name Which clock to enable, see \ref clock_ip_name_t. */

* @brief Abort any on-going DMA channel transfer (Blocking mode). * @param hdma : Pointer to a DMA_HandleTypeDef structure that contains the confi

* @brief Release the lock of the semaphore. * @note In case of LL_HSEM_1StepLock usage to lock a semaphore, the process is 0. * @rmtoll R

Get ac_buffer builder's underlying ac_buffer * \param pBuilder ac_buffer builder * \return ac_buffer */

* ppp_warn - log a warning message. */

* @ingroup tcp_raw * Find out what we can send and send it * * @param pcb Protocol control block for the TCP connection to send data * @return ERR

* @brief Wait for a FLASH operation to complete. * @param Timeout maximum flash operation timeout * @retval HAL Status */

/ ! * \brief Dequeue a message. * * \param pQueue Pointer to queue. * \param pHandlerId Handler ID of returned message; this is a retu

\brief Get Priority Mask \details Returns the current state of the priority mask bit from the Priority Mask Register. \return Prio

@defgroup RCCEx_Exported_Functions_Group1 Extended Peripheral Control functions * @brief Extended Peripheral Control functions * @verbatim ======

* @brief Initialize the CPU, AHB and APB busses clocks according to the specified * parameters in the RCC_ClkInitStruct. * @param RCC_Cl

Start a critical section for thread safety.

* @brief Start the DMA data transfer. * @param hdma DMA handle * @param src : The source memory Buffer address. * @param dst : The

/ ! * \brief Set an event for an event handler. * * \param handlerId Handler ID. * \param event Event or events to set. */ /

Scope(A), as defined in RFC 6724 plus RFC 4007 */

Send a debug message to the user.

/ Conversion functions //////

* @brief Write generic device register * * @param ctx read / write interface definitions(ptr) * @param reg register to write * @param

* Signed subtraction: X = A - b */

* Put an element back into its pool. * * @param type the pool where to put mem * @param mem the memp element to free */

! \brief enable the peripherals clock \param[in] periph: RCU peripherals, refer to rcu_periph_enum only one parameter ca

! * @brief Disable the clock for specific IP. * * @param name Which clock to disable, see \ref clock_ip_name_t. */

* @brief Handles FMPI2Cx communication when starting transfer or during transfer (TC or TCR flag are set). * @param hfmpi2c FMPI2C handle. * @pa

* @brief Handles I2Cx communication when starting transfer or during transfer (TC or TCR flag are set). * @param hi2c I2C handle. * @param DevA

* @brief Handles I2Cx communication when starting transfer or during transfer (TC or TCR flag are set). * @param hi2c I2C handle. * @param DevA

* @brief Handles I2Cx communication when starting transfer or during transfer (TC or TCR flag are set). * @param hi2c I2C handle. * @param DevA

* @brief Handles I2Cx communication when starting transfer or during transfer (TC or TCR flag are set). * @param hi2c I2C handle. * @param DevA

* @brief Handles I2Cx communication when starting transfer or during transfer (TC or TCR flag are set). * @param hi2c I2C handle. * @param DevA

* @brief Handles I2Cx communication when starting transfer or during transfer (TC or TCR flag are set). * @param hi2c I2C handle. * @param DevA

* @brief Handles I2Cx communication when starting transfer or during transfer (TC or TCR flag are set). * @param hi2c I2C handle. * @param DevA

* @brief Handles I2Cx communication when starting transfer or during transfer (TC or TCR flag are set). * @param hi2c I2C handle. * @param DevA

* @brief Handles I2Cx communication when starting transfer or during transfer (TC or TCR flag are set). * @param hi2c I2C handle. * @param DevA

* @brief Handles I2Cx communication when starting transfer or during transfer (TC or TCR flag are set). * @param hi2c I2C handle. * @param DevA

* @brief Handles I2Cx communication when starting transfer or during transfer (TC or TCR flag are set). * @param hi2c I2C handle. * @param DevA

/ * @brief * Enable/disable oscillator. * * @note * WARNING: When this function is called to disable either cmuOsc_LFXO or * cmuOsc_HFXO, t