@brief Delays for a desired amount of cycles while also waiting for a status to equal OR not-equal to a value. @param ui32usMaxDelay - Maximum number

* \brief A function to read networking address informations. * \param addr_id identifies the address information type to be read. * \param address i

Replacement for generic wait functions to avoid invoking OS scheduling stuff. */

* \brief Change specific bits in a 32 bits word. * * \param[in,out] word Pointer of the word to change * \param[in] bits bits_l

As crypto init counter changes from 0 to 1: * * 1. Enable crypto clock * 2. Enable crypto interrupt */

As crypto init counter changes from 1 to 0: * * 1. Disable crypto interrupt * 2. Disable crypto clock */

handle EXTI interrupt in EXTI0 to EXTI15 * @param irq_index the line of EXTI(0~15) */

handle EXTI interrupt in EXTI0 to EXTI15 * @param irq_index the line of EXTI(0~15) */

* Get the characteristic's properties. * * @note Refer to GattCharacteristic::Properties_t. * * @return The characteristic's prope

@brief Read HM01B0 registers @param psCfg - Pointer to HM01B0 configuration structure. @param ui16Reg - Register address.

/ ! * \brief Insert at the tail of the list. * * \param pList Pointer to the list. * \param pFtParam Flush timeout paramete

/ ! * \brief Check if the list is empty or not. * * \param pList Pointer to the list. * * \return True if successfully remov

/ ! * \brief Initialize flush timeout parameters. * * \param pFtParam Pointer to the flush parameter. * \param bn

/ ! * \brief Start LLCP timer. * * \param pCtx Connection context. */ /

/ ! * \brief Unpack an advertising channel PDU header. * * \param pHdr Unpacked header. * \param pBuf Packed packet buffer. *

* Baseline multiplication: X = A * b */

Check whether a key identifier is null. * * \param key Key identifier. * * \return Non-zero if the key identifier is null, zero otherwise. */

* Call the lower part of a netconn_* function * This function is then running in the thread context * of tcpip_thread and has exclusive access to lw

* @ingroup netif * Remove a network interface from the list of lwIP netifs. * * @param netif the network interface to remove */

Dispatch specified Thread or Ready Thread with Highest Priority. \param[in] thread thread object or NULL.

* @see ble::post */

* Claculate Prefix bits to bytes count * * \param prefixLenInBits len in bits * * return Byte length */

! \brief get the clock stabilization and periphral reset flags \param[in] flag: the clock stabilization and periphral reset flags, refer

* Get index of serial object TX IRQ, relating it to the physical peripheral. * * @param obj pointer to serial object * @return internal NVIC TX IRQ in

Get the seqno of a segment (by index) on the ooseq list * * @param pcb the pcb to check for ooseq segments * @param seg_index index of the segment

Get the tcplen (datalen + SYN/FIN) of a segment (by index) on the ooseq list * * @param pcb the pcb to check for ooseq segments * @param seg_index

/ ! * \brief Get the peer ID address. * * \param pFiltResults Filter results. * \param pPeerIdAddr Storage for peer I

/ * @brief * Send a request for writing or reading RAM of the Message Object msgNum. * * @param[in] can * A pointer to the CAN peripheral regi

* @brief This function enable module clock * @param[in] u32ModuleIdx is module index. Including : * - \ref PDMA_MODULE * - \ref ISP_MODULE

* @brief Enable module clock * @param[in] u32ModuleIdx is module index. Including : * - \ref PDMA_MODULE * - \ref

! * brief Get current PLL output frequency. * * This function get current output frequency of specific PLL * * param pll pll name to get freque

! * @brief Set CCM MUX node to certain value. * * @param mux Which mux node to set, see \ref clock_mux_t. * @param value Clock mux value to set,

/ * @brief * Read 256 bits of data from a DDATAX register in the CRYPTO module. * * @details * Read 256 bits of data from a DDATAX (Double Dat

* @brief Writes Key in Key registers. * @param hcryp: pointer to a CRYP_HandleTypeDef structure that contains * the configuration inform

* Function Name: Cy_DMA_Channel_Disable ****************************************************************************/ * * The function is used to disa

* Function Name: Cy_SCB_ReadRxFifo ****************************************************************************/ * * Reads a data element directly out

! * @brief Gets the remaining bytes of the current DMA transfer. * * @param base DMA peripheral base address. * @param channel DMA channel number.

/ ! * \brief For internal use only. Execute DM callback from SMP procedures. * * \param pDmEvt Pointer to callback event data. * * \retu

! * brief Submits the eDMA transfer request. * * This function submits the eDMA transfer request according to the transfer configuration structure.

! * @brief Enable specific interrupt. * * Enable the interrupt not routed from intmux. * * @param interrupt The IRQ number. */

* @brief Wait for a FLASH operation to complete. * @param Timeout maximum flash operation timeout * @retval HAL_StatusTypeDef HAL Status */

! * brief Get the FlexCAN instance from peripheral base address. * * param base FlexCAN peripheral base address. * return FlexCAN instance. */

* @brief Manage the disabling of Interrupts. * @param hfmpsmbus Pointer to a FMPSMBUS_HandleTypeDef structure that contains * the

* @brief Return the peripheral clock frequency for a given peripheral(SAI..) * @note Return 0 if peripheral clock identifier not managed by this

* @brief Returns the PCLK1 frequency * @note Each time PCLK1 changes, this function must be called to update the * right PCLK1 value. O

! * @brief Sets the IOMUXC pin configuration. * @note The previous five parameters can be filled with the pin function ID macros. * * This is an e

! * @brief Sets the IOMUXC pin mux mode. * @note The first five parameters can be filled with the pin function ID macros. * * This is an example t

* @brief Get the selected ADC instance enable state. * @note On this STM32 series, flag LL_ADC_FLAG_ADRDY is raised when the ADC * is e

* @brief Set parameter common to several ADC: measurement path to internal * channels (VrefInt, temperature sensor, ...). * @note One o

* @brief Force AHB1 peripherals reset. * @rmtoll AHB1RSTR GPIOARST LL_AHB1_GRP1_ForceReset\n * AHB1RSTR GPIOBRST LL_AHB

* @brief Release AHB1 peripherals reset. * @rmtoll AHB1RSTR GPIOARST LL_AHB1_GRP1_ReleaseReset\n * AHB1RSTR GPIOBRST LL

* @brief Get System prescaler * @rmtoll D1CFGR/CDCFGR1 D1CPRE/CDCPRE LL_RCC_GetSysPrescaler * @retval Returned value can be one o

* @brief Get HSE sysclk and pll prescaler * @rmtoll CR HSEPRE LL_RCC_HSE_IsEnabledDiv2 * @retval None */