* @brief Returns the FLASH Read Protection level. * @retval FLASH ReadOut Protection Status: * This parameter can be one of the following

* @brief Set the read protection level. * @param ReadProtectLevel specifies the read protection level. * This parameter can be one of th

! * brief Get instance number for FLEXIO module. * * param base FLEXIO peripheral base address. */

* @brief Disable FMC ISP function. * @return None */

* @brief Enable FMC ISP function * @return None */

* @brief Execute FMC_ISPCMD_READ command to read a word from flash. * @param[in] u32Addr Address of the flash location to be read. *

\fn int32_t GPDMA_ChannelConfigure (uint8_t ch, uint32_t src_addr,

\fn uint32_t GPDMA_ChannelGetCount (uint8_t ch) \brief Get number of transferred data \param[in] ch Channel number (0..7) \retu

\fn int32_t GPDMA_PeripheralSelect (uint8_t peri, uint8_t sel) \brief Selects GPDMA requests \param[in] peri GPDMA peripheral \

! * @brief Sets the output level of the multiple GPIO pins to the logic 0. * * @param base GPIO peripheral base pointer (GPIOA, GPIOB, GPIOC, and s

* @brief Perform a mass erase or erase the specified FLASH memory pages * @note To correctly run this function, the @ref HAL_FLASH_Unlock() funct

* @brief This function configures the source of the time base. * The time source is configured to have 1ms time base with a dedicated *

* @brief Initializes the CPU, AHB and APB buses clocks according to the specified * parameters in the RCC_ClkInitStruct. * @param RCC_C

* @brief Get the RCC_ClkInitStruct according to the internal * RCC configuration registers. * @param RCC_ClkInitStruct pointer to an RCC_ClkIni

* @brief Returns the PCLK1 frequency * @note Each time PCLK1 changes, this function must be called to update the * right PCLK1 val

* @brief Hall commutation changed callback in non blocking mode * @param htim : TIM handle * @retval None */

* @brief Starts the TIM Base generation. * @param htim : TIM handle * @retval HAL status */

* @brief Period elapsed callback in non blocking mode * @param htim : TIM handle * @retval None */

* @brief Hall Trigger detection callback in non blocking mode * @param htim : TIM handle * @retval None */

* @brief UART error callbacks. * @param huart: Pointer to a UART_HandleTypeDef structure that contains * the configuration inform

* @brief Rx Transfer completed callbacks. * @param huart: Pointer to a UART_HandleTypeDef structure that contains * the configura

* @brief Tx Transfer completed callbacks. * @param huart: Pointer to a UART_HandleTypeDef structure that contains * the configura

* @brief USART error callbacks. * @param husart: Pointer to a USART_HandleTypeDef structure that contains * the configuration in

* @brief Tx Transfer completed callbacks. * @param husart: Pointer to a USART_HandleTypeDef structure that contains * the config

! * @brief Enables or disables the I2C peripheral operation. * * @param base I2C base pointer * @param enable Pass true to enable and false to dis

! * brief Enables I2C interrupt requests. * * param base I2C base pointer * param mask interrupt source * The parameter can be combination of

! * brief Sends a START on the I2C bus. * * This function is used to initiate a new master mode transfer by sending the START signal. * The slave

! * brief Performs a polling send transaction on the I2C bus. * * param base The I2C peripheral base pointer. * param txBuff The pointer to the d

\fn int32_t ARM_I2C_PowerControl (ARM_POWER_STATE state, I2C_RESOURCES *i2c) \brief Control I2C Interface Power. \param[in] state

Check if running Privileged \return true=privileged, false=unprivileged

! * brief Clears the external wakeup source flag. * * This function clears the external wakeup source flag for a specific pin. * * param base LLW

! * brief Gets the external wakeup source flag. * * This function checks the external pin flag to detect whether the MCU is * woken up by the spec

! * brief Sets the external input pin source mode. * * This function sets the external input pin source mode that is used * as a wake up source.

Enable OS Tick.

Get OS Tick count value.

SWCLK/TCK I/O pin: Set Output to Low. Set the SWCLK/TCK DAP hardware I/O pin to low level. */

SWCLK/TCK I/O pin: Get Input. \return Current status of the SWCLK/TCK DAP hardware I/O pin. */

SWCLK/TCK I/O pin: Set Output to High. Set the SWCLK/TCK DAP hardware I/O pin to high level. */

SWDIO I/O pin: Switch to Input mode (used in SWD mode only). Configure the SWDIO DAP hardware I/O pin to input mode. This function is called prior \re

SWDIO/TMS I/O pin: Get Input. \return Current status of the SWDIO/TMS DAP hardware I/O pin. */

TDI I/O pin: Get Input. \return Current status of the TDI DAP hardware I/O pin. */

nTRST I/O pin: Get Input. \return Current status of the nTRST DAP hardware I/O pin. */

! * @brief Clears the multiple pin interrupt status flag. * * @param base PORT peripheral base pointer. * @param mask PORT pin number macro. */

! * @brief Reads the whole port status flag. * * If a pin is configured to generate the DMA request, the corresponding flag * is cleared automati

Resume Trace Capture

* * SEGGER_RTT_Write * * Function description * Stores a specified number of characters in SEGGER RTT * control block which is then read

! * brief Recovers after wake up from stop modes. * * This function should be called after wake up from STOP/VLPS/LLS/VLLS modes. * It is used wit

! * brief Prepares to enter stop modes. * * This function should be called before entering STOP/VLPS/LLS/VLLS modes. */

Enable or disable SWO Mode (Manchester) enable: enable flag return: 1 - Success, 0 - Error

Enable or disable SWO Mode (UART) enable: enable flag return: 1 - Success, 0 - Error

Increment Semaphore tokens. \param[in] semaphore semaphore object. \return 1 - success, 0 - failure.

Set Pending SV (Service Call) Flag

Set Trace Error flag(s) flag: error flag(s) to set

\fn int32_t Set_Channel_active_flag (uint8_t ch) \brief Protected set of channel active flag \param[in] ch Channel number

Common clock delay calculation routine clock: requested SWJ frequency in Hertz return: void

\brief System Tick Configuration \details Initializes the System Timer and its interrupt, and starts the System Tick Timer. Counter is

* @brief Time Ouput Compare 3 configuration * @param TIMx to select the TIM peripheral * @param OC_Config : The ouput configuration structure